Car Digital Paint Coating Thickess Guage Tester Auto Meter Measuring Kit Tool US

Description

VDIAGTOOL VC100/VC200/VC300 Car Thickness Gauge Paint Coating VC200 Car Paint Tester With LCD Backlight Measuring Fe/NFe Car Accessories US Shipping
Car Digital Paint Coating Thickess Guage Tester Auto Meter Measuring Kit Tool US
Car Coating Thickness Gauge
VC100 Car Coating Thichness Gauge:
Car Paint Tester Introduction
The Car Paint Tester is a portable obd2 obdii coating thickness gauge,which can meansure the thickness of non-metallic coating(such as paint,film,etc.) On netal substrate quickly,nondestructively,and accuratly.It is mainly used to measure the thickness of the vehicle's surface paint and other coating meaurement.
Car Paint Tester Button Functions
1.Botton"CLR":Turn on/off,clear.
2.Botton"UNIT":Unit Switch,backlight
Car Paint TesterOperation Instructions
1.Measurement preparation
Open battery cover and load two CR2032 button batteries(Not Includes); Pay attention to positive and negative pole.
2.Turn on/off
Leave the instrument hang in the air and press"CLR"button to turn it on,LCD full screen display,which means it enters the measurement state.Then long press"CLR"button to turn it off.
Note:Keep it away from the substrate when starting up.
3.Measurement
Press the probe onto the coated metal substrate lightly,ensure that the instrument should be perpendicular to the surface of the object that being measured.
Note:When the probe was pressed on the substrate,the LCD will display"---",then you must wait unit the measurement value displayed the LCD,then remove it from the substrate.If removing before a value is displayed,it will display the last measured value.
4.Unit selection
After start-up,short press"UNIT"button to select measurement unit mm or mil.
5.LCD backlight
After start-up,long press"UNIT"button to turn on/off the backlight.
6.Clear screen data
After start-up,press"CLR"button to clear the data displayed on LCD screen.
7.Power off automatically
The Car Paint Tester will power off automatically if two minutes no operation after start-up.And it will power off automatically as well after five minutes start-up,even when you are operating it.
Note: If The Screen Show You "OL" It Means Over Range,Can Test Range(0-1.80mm/0-71.0mil)
VC200 Car Coating Thickness Gauge
The VC200 can make a quick and effective measurement of the thickness of the non-metallic coating on the non-magnetic metal substrate and the thickness of the non-magnetic coating of the magnetic metal substrate,it can also automatically identify the magnetic metal substrate and non-magnetic metal substrate.It is widely used in the inspection field of automobile manufacturing,metal processing industry,chemical industry,commodity inspection,etc.
Product Functions
1.Measuring the thickness of non-magnetic coating on the magnetic metal substrate.
2.Measuring the thickness of the non-metallic coating on the non-magnetic metal substrate.
3.Automatically identifying the non-magnetic metal substrate and magnetic metal substrate.
4.Single measurement,continous measurement and differential measurement available.
5.With maximum,minimum and average value viewing function.
6.Zero-point calibration,offset calibration and basic calibration available.
7.Metric and imperial units of measurement optional.
8.LCD backlight.
9.Automatic shutdown.
Measurement Modes
1)Single measurement:measuring one data for each measurement. 2)Continuous measurement:As long as the probe remains on substrate surface,the instrument keeps measuring. 3)Difference measurement:the difference between this measurement and the last measurement.
How to judge automobile paint?
The thickness of the original car paint is between 100-200um,but the thickness of the touch up paint will be clear.It may be 500-1000um or even thicker. According to the standard of economical automobile,the paint surface of automobile should not be less than 90um,90um is regarded as cutting corners. For any cars standard higher than USD50000,the paint surface shall not be lower than 120um(hard index) Below 120um is considered as cutting corners.
VC300 Car Coating Thickness Gauge
The VC300 is a color-screen portable coating thickness gauge with high-definition display,which can quickly,non-destructively and accurately measure non-magnetic coating thickness on magnetic metal substrates and non-metallic coating thickness measurement on non-magnetic metal substrates.At the same time it can automatically identify magnetic metal substrate and nin-magnetic metal substrate,and is widely used in manufacturing,metal processing industry,chemical industry,commodity inspection and other testing areas.
Features
1.Meny operation and color-screen HD display.
2.Voice broadcast function.
3.There are two measurement methods, single and continuous.
4.The thickness measurement of the non-magnetic coating on the surface of the magnetic metal substrate and the thickness measurement of the non-metal coating on the non-magnetic metal substrate.
5.It has two calibration functions: basic and zero point.
6.Metric and English unit selection and storage function.
7.Screen rotation, charging protection, multiple interface display, screen brightness selection.
8.Automatic shutdown selection function.
Noted
1.Keep the probe away from the meaured substrate when starting up.
2."OL"indicates that the value exceeds measurement range.
3.Do not press the sensor with your finger or other object into the instrument,because this operation may damage the sensor parts and the instrument
Measurement Modes:
1)Single measurement:measuring one data for each measurement.
2)Continuous measurement:As long as the probe remains on substrate surface,the instrument keeps measuring.
3)Difference measurement:the difference between this measurement and the last measurement.
Calibration Operation
1.Basic Calibration:
a.Prepare the calibration plate and calibration base,enter calibration menu and select basic calibration.
b.According to the instrument instruction,place the corresponding calibration plate for calibration.
c.After calibration is completed,"calibration complete"will show up at the bottom of the screen and the instrument will return to the previous interface.
d.After the calibration is complete,you can go back to measurement interface and perform measurement.
e.Magnetic and non-magnetic metal base calibration do not affect each other.
Note:When preforming basic calibration,press the instrument onto substrate when the arrow is down,and remove it when the arrow is up.
2.Zero Calibration:
a.Enter calibration menu and select zero calibration.
b.Lightly press the instrument onto substrate.
c.The instrument will automatically calibrate to zero point.
d.The instrument displays the previous interface after calibration is done.
e.After calibration is complete,you can go back to meansurement interface and perform measurements.
How to judge automobile paint?
The thickness of the original car paint is between 100-200um,but the thickness of the touch up paint will be clear.It may be 500-1000um or even thicker.
According to the standard of economical automobile,the paint surface of automobile should not be less than 90um,90um is regarded as cutting corners.
For any cars standard higher than USD50000,the paint surface shall not be lower than 120um(hard index) Below 120um is considered as cutting corners.
Payment
Delivery details
Terms of sales
About us
Contact us
Payment
1.We accept
Credit cards、Debit card、Apple Pay、Google Pay、PayPal ect.
payment.
2.Please contact us if you need to use another method to pay.
3.Payment should be made within 4 days after bidding ends.
4.Otherwise an Unpaid Item case will be opened to you.
5.We are not responsible for buyers’ local taxes.
6.Please include your special requests in eBay note if there is any.
7.We reserve the final right of selling
Delivery details
Shipping:
Order will be shipped within
1-3 business day
after payment confirmed.
We have warehouse in
USA，UK，Australia and China
warehouse.
From our US/UK/AU warehouse via UPS or DHL eCommerce shipping.
Delivery time varies from 2 to 6 business days.
From our Hong Kong warehouse via DHL or FedEx Ground
Delivery time varies from 3 to 10 business days.
From our China warehouse
For US Buyers, we use SpeedPAK (Delivery time is 7-25 business days) or express delivery(Delivery time is 3-10 business days) .
For other countries' buyers, we use SpeedPAK / China Post (Delivery time varies from 10 to 30 business days)or Express delivery(Delivery time is 3-10 business days).
We will ship according to your eBay or PayPal address.
Please make sure it is correct and include phone number for delivery.
If you do not receive your order in the estimated time, please contact us, we would do our best to serve you solve the problem.
Please include your special requests in eBay note if there is any.
We will try our best to give customers good and pleasant parchasing experience.
Welcome your any-time order :)
Terms of sales
We are
Online
Store
, our all items are
100% original
and Our devices have warranty.
12 months free repair for the devices.
3 months for the accessories.
Please contact us firstly when you need warranty service.
In case an item arrives faulty, please contact us in 30 days and keep it unused. You must tell us what the defect is and give us your eBay ID.
We will instruct you on how to return and get refund or replacement.
If after 30 days, or the item has been used, we have the right to decline your claim.
Items should be returned on buyers' cost for repair or replacement.
Terms of tax:
We are not responsible for buyer's local taxes, please consult your local Customs for tax details.
About us
Who We Are?
We are specialized dealer of On-Board Diagnostic tools and automotive electronics
For more than 10 years.
We are authorized first class distributor of XTOOL,
Xhorse,
VXDIAG, VDIAGTOOL,  XTUNER brands.
and more brands will be show in our store in near future.
If you like our products, please add our eBay shop to your "My Favorites" list.
What Do We Have?
We have office and warehouse in Australia and US to ensure fast shipment and after-sale service.
We have more than 60 employees devoting to customer satisfaction.
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us.
Please let us know the problem BEFORE you give us or feedback, so that we can satisfactorily address your concerns.
Contact us
Our customer-oriented service strives for positive feedbacks with all 5 star selling ratings.
Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case.
We will reply in 24 business hours.
Business time: GMT8 (9:00-18:00) from Monday to Friday.